Free Pattern: Heart Frame Bracelet by Abby Hook

By on July 24, 2017
Print Friendly

by Judy Ellis, Wirejewelry.com

Wire Jewelry Pattern for July 24th, 2017

Heart Frame Bracelet

by Abby Hook

Repetition of a simple shape in a design can create a striking effect, it is also the best way to master a technique and open spirals can be tricky!
This lesson teaches you how to make little heart shaped frames and then how to hammer them.
The finished size of the bracelet is 7 1/2”. It is easy to adjust the size by adding or subtracting links or heart frames.

Materials:

Tools:

Directions:

Step 1: This bracelet is made using several heart shaped links, which are then connected together with jump rings.
To begin with we need to form all the hearts. Start by cutting 6 x 4” pieces of 18 gauge wire.
Straighten each piece by grasping one end with the flat nose pliers and pulling the length of wire through the jaws of the nylon jaw pliers a couple of times.

element_5415_abby-hook_heart-frame-bracelet_IMG_1236

Step 2: At the center point of each piece of wire, make a 45 degree bend with chain-nose pliers.

element_5416_abby-hook_heart-frame-bracelet_IMG_1239

 

Step 3: Grasp one end with the centre of the jaws of the round nose pliers and form a loop approx. 1/4” across.
Repeat on the other side.
Trim the tips of the wires off to create tapered ends.
File and sand the ends smooth. Make sure you remove any sharp edges – remember these frames are going to be sitting against the skin.
element_5417_abby-hook_heart-frame-bracelet_IMG_1248 element_5418_abby-hook_heart-frame-bracelet_IMG_1251 element_5419_abby-hook_heart-frame-bracelet_IMG_1254

Step 4: Turn the pliers to form an open spiral, ensuring the gap is even all the way round.
Repeat on the other side, so that it is a mirror image.
The heart should meet in the middle, if it doesn’t, adjust the bend in the middle.
The heart should measure just under 1” across and tall.

element_5420_abby-hook_heart-frame-bracelet_IMG_1258 element_5421_abby-hook_heart-frame-bracelet_IMG_1260 element_5422_abby-hook_heart-frame-bracelet_IMG_1263

Step 5: Lay your heart on the bench block or anvil and carefully hammer the curves at the top of the heart and the very tip of the point.
Make sure you keep the hammer at a 90° angle to the block, so that you hit the wire squarely each time.
Use several little taps to flatten the wire, rather than one big whack.
Notice how the hammering caused the wire heart to open up and change shape slightly. Adjust as necessary.
element_5423_abby-hook_heart-frame-bracelet_IMG_1268 element_5424_abby-hook_heart-frame-bracelet_IMG_1271

Step 6: Make another 5 hearts, so that you have 6 in total.

element_5425_abby-hook_heart-frame-bracelet_IMG_1274

Step 7: Cut a 4” piece of 28 gauge wire.
Attach it to one of the open loops, just before the open loops meet, by coiling 3 times leaving a small tail to hold onto.
Bind the center together 5 times, securing the heart closed and also strengthening it.
Note: – Be careful when binding, not to pull too tightly, as this will cause the frame to overlap itself slightly.
Coil 3 times to secure.
Trim the 28 gauge wire tails on the inside of the frame and tuck the ends in, using the chain nose pliers.
Squeeze the binding flat with the nylon jaw pliers. Repeat on all 6 hearts.

element_5426_abby-hook_heart-frame-bracelet_IMG_1277 element_5427_abby-hook_heart-frame-bracelet_IMG_1280 element_5428_abby-hook_heart-frame-bracelet_IMG_1283

Step 8: The hearts are connected together with multiple jump rings. They are made on a 4mm mandrel. Cut a 22” length of 18 gauge wire and straighten.
Position the wire at a 90° angle to the mandrel, leaving a 1” tail to hold onto.
Wrap the wire around the mandrel, forming the first jump ring.
Ensure you keep the wire straight, so that the finished jump rings are consistently sized and shaped.
Keep coiling until you have used all the wire.
element_5429_abby-hook_heart-frame-bracelet_IMG_1286 element_5430_abby-hook_heart-frame-bracelet_IMG_1289 element_5431_abby-hook_heart-frame-bracelet_IMG_1292

Step 9: The proper way to cut jump rings is with a jewellers saw, but it is possible to do it with flush cutters.
Cut the small straight wire ends from the coil, making sure that the flush edge of the cutters is against the ring.
Trim both ends on each jump ring with the flush side of your cutters, so that the rings meet perfectly.
Notice that by trimming the pinched nib from the end, you lose a tiny piece of wire each time, so that you end up with fewer jump rings than the number of coils you had.
Note: – each ring uses approx. 2/3” of 18 gauge wire.

element_5432_abby-hook_heart-frame-bracelet_IMG_1295 element_5433_abby-hook_heart-frame-bracelet_IMG_1298

Step 10: Now that all of the components have been made, the bracelet can be connected together.
To open a jump ring, twist one end of the wire away from the other as shown.
Never pull open as this action not only distorts the finished shape of the ring, as shown in the picture, it also fatigues the metal, making it more brittle and subject to breaking.

element_5411_abby-hook_heart-frame-bracelet_IMG_1301 element_5412_abby-hook_heart-frame-bracelet_IMG_1304

Tip: – It is easier to connect the hearts if they sit on top of each other.
When you close the ring, rub the ends against each other a couple of times, by twisting left and right. This burnishes the metal slightly and also hardens the ring, making it stronger.
Use 3 rings on each curve and 2 on each point. Connect 6 hearts as shown

element_5434_abby-hook_heart-frame-bracelet_IMG_1310 element_5435_abby-hook_heart-frame-bracelet_IMG_1313

Step 11: Connect the hook clasp to one end with 2 rings and add one ring to the other end, for the clasp to link to. Check out my hook clasp tutorial on making a handmade hook.
Notice how the rings can move around the hearts when not being worn.
The finished size of this bracelet is 7 1/2”. You can add or subtract jump rings and heart frames to increase or decrease the length.
element_5436_abby-hook_heart-frame-bracelet_IMG_1316

Happy Wrapping!

Click to Receive Daily Tips by Email

One Comment

  1. avatar

    Belinda Miller

    July 24, 2017 at 9:02 am

    Love the heart chain. Very pretty. Concise directions